Sunday, 9 September 2018

Victorian Corset



As I embark on a new sewing adventure, I have made a Victorian Corset to fit under a Victorian Bustle Dress. Yes, I have decided to create something completely frivolous that I may never wear out in public. But it is a lot of fun to plan. 

A proper Victorian outfit needs the proper foundations. It is probably a good thing that the most daunting garment needs to be tackled first, kind of like eating your vegetables. Such a challenging construction almost put me off the whole endeavour, but it has been far less challenging than I expected, and I am pretty pleased with myself for how well it turned out.



I bought Truly Victorian's TV110 Corset as an e-pattern and made the first toile from a cotton business shirt. I cut a size D with a B cup. I shortened the waist by an inch, at the waistline. I made this without bones and I laced the back with knitting yarn by punching holes in the back with a knitting needle - because I didn't even have an awl yet. I sewed the front shut - no busk. Based on this try on, I decided to size down the cup and size up the waist area. I was pleased enough with this to go ahead and order the proper supplies from Sew Curvy.


For the real version, I cut a size D and graded out at the waist to a size E. I did the cup size A. 

While I was putting it together, I lost my nerve and started reducing the size of the seam allowances. It was coming up so small! When I put the first three pieces together and held them up to myself, what was meant to be the side seam was about 1/8 of the way around my body. I kept going, deciding that it was better to finish it as a toile and decide what should be done differently afterwards. I was determined not to abandon it half way through. I didn't actually have a proper idea of what I should change anyway. 

So I sewed it up and closed off the back edges. Then I sewed the boning channels and inserted the bones. Sewing the boning channels was actually really fun. I decided to put them beside the seam where the seam allowance was not. The pattern calls for topstitching the seam allowance down and adding the boning channel beside that. My machine was struggling with four layers of coutil, so I didn't want to finish it off by making it sew through six layers. Putting the boning on the other side gives it less bulk and the seam allowances balance out the boning plus give a modicum of strength opposite each bone. 

Making a two layer corset seems like a bit of a faff at the time, but I can fully appreciate how much easier it is than adding boning channels. Especially if you have to make your channels out of self fabric. All I had to do was run a seam beside the existing one and push the bone in. So easy.


I decided to add the laces without grommets to check the fit first. I put one straight bone in the back, but didn't place it very well. I could see an issue with my sway back in the fit of the lacing over the back waist area. It was very puckered, even with the bone. I wasn't exactly sure how to fix a sway back in a corset, but it definitely needed less fabric in this area. I pinched out a wedge but then straightened up the back edges from top to bottom. It added quite a bit of fabric back into the waist circumference.


I was truly surprised, when I tried it on, at how well it fitted. I was delighted because where I thought I was going to have to re-make the entire thing, with new coutil and a shorter busk, I now only had to re-do the back piece and buy one pair of shorter spiral bones.

I had also realised that the bottom edge was too low, and would dig into the top of my legs when I sat down. This was pretty disappointing, since I had bought pre-cut bones, based on the measurements from my first toile.

But I ordered more supplies and put the too-long bones to good use. I re-positioned them on the centre line of the corset pieces. Each piece is boned twice, once at the side seam and once in the centre. There are also flat steel bones at either side of the busk and on both sides of the eyelets. 18 spiral steels, 6 flat steels, the busk and 12 eyelets. The whole thing is very heavy but I love the armoured plate effect that the three bones in the first panel give where they meet at the bottom.


The fit seems to be pretty good. I have a about 1 to 1.5 inches of lacing gap, but the back is even throughout the laces. The fit in the front of the bust seems pretty good. It is not particularly supportive, and there is not a proper amount of "spillage" at the top. Unfortunately, all the spillage is at the back, not the front. I think that is more a problem of my body than the fault of the corset. I am not sure what to do about the back fat spillage though. The tight areas have to press the flesh somewhere but this will show with a fitted bodice over the top. I'll probably have to make a corset cover but I think it might not be enough.  Not very pretty, but look at that that straight lacing gap!


The waist fits really well. I think I shortened it by the right amount and the fit is snug but not uncomfortable. There is no pressing on my hips, which is what my short waist usually leads to. I love how the corset makes me look the right shape and flattens my tummy! I got a 3 inch reduction. Now, how to wear this in real life...

The fit at the bottom of the hip is not quite as perfect but I am not going to fuss with it. I am so pleased with the overall general fit and it has come out a lot better than I expected, especially with my usual short waist issues.


I flossed the bottom of the bones before adding the edge tapes. These were done with linen thread because I had it with no real use for it and I really like the pale taupe colour against the white. All the stitches are different, I couldn't get it perfectly even. One of them is done backwards (as is one of the eyelets), but who's looking? The edges are trimmed with cotton twill fabric, also from the stash. I only broke one needle in the process of adding it - although there were some close calls. I didn't do a great job of matching the points at the bottom front. These parts of the tape were very thick and I was having an epic battle with my sewing machine just to get them folded under. They will be under the skirts and the whole thing will be under the dress, so it is only for Instagram that I even need to think about it.


I added the lace by hand at the end. Partly because it is very narrow and I would have struggled to catch it into the edges, but mostly because I forgot until I was halfway through. It is polyester, but I had plenty of it, harvested from the nightgown.

I'm actually pretty surprised that it has turned out as nice as it has. It's a lovely pattern to start with and it looks fab all made up. The coutil got a bit dirty in my iron, and with all the handling, but if you squint, you can pretend that it is due to age. As a very first corset, from an amateur maker, I'd say it's pretty amazing.

Now on to the petticoats!


Costs:
 Fabric: Sew Curvy; £10.50
 Pattern: Truly Victorian; £7.87
 Notions: busk, flat steels, spiral steels, eyelets, lacing cord, teflon tape, thread, shipping; £39.96
 Tools: eyelet setter, awl, machine needle; £3.24
Total: £61.57

No comments:

Post a Comment

ShareThis

LinkWithin

Related Posts Plugin for WordPress, Blogger...